Craftsman 139.5364812 El manual del propietario

Owner's Manual/Manual Del PropietarioII:RRFTSMRNI112 HPGARAGE DOOR OPENERABRIDOR DE PUERTA DE COCHERAFor Residential Use Only/Solo para uso resid

ASSEMBLY STEP 4Install the Chain/Cableand Attach the Sprocket CoverINSTALLING THE CHAIN/CABLE1. Pull the cable loop from thecarton and fasten it to th

ASSEMBLY STEP 5Tighten the Chain and Cable• Spin the inner nut and lock washer down thethreaded shaft, away from the trolley.• To tighten the chain, t

INSTALLATION STEP 1Determine the Header BracketLocationTo prevent possible SERIOUSINJURYor DEATH:• Headerbracket MUST be RIGIDLYfastenedtostructural s

INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wailabove the garage door, or to the ceiling. Follow thei

Header Wall/ Header//_ BracketCablePulleyBracketINSTALLATION STEP 3Attach the Rail to the HeaderBracket• Position the opener on the garage floor below

INSTALLATION STEP 4Position the OpenerFollow instructions which apply to your door type asillustrated.SECTIONAL DOOR OR ONE-PIECE DOOR WITHTRACKA 2x4

INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yoursmay be different. Hanging brackets should be angled(Figure 1) to

INSTALLATION STEP 6Install the Door ControlLocate door control within sight of door, at a minimumheight of 5 feet (1.5 m) where small children cannotr

INSTALLATION STEP 7Install the Light• Install a 75 watt maximum light bulb in the socket.The light will turn ON and remain lit forapproximately 4-1/2

INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shock,

TABLE OF CONTENTSIntroduction 2-7Safety symbol and signal word review ... 2Preparing your garage door ...

INSTALLATION STEP 10Install The Protector System ®The safety reversing sensor must be connectedand aligned correctly before the garage dooropener will

INSTALLINGTHEBRACKETSFigure1,2 and3showrecommendedassemblyofbracket(s)and"C"wrapbasedonthewaftinstallation of the sensors on each side of th

MOUNTING AND WIRING THE SAFETY SENSORS• Slide a 1/4"-20xl/2" carriage bolt head into the sloton each sensor. Use wing nuts to fasten sensors

INSTALLATION STEP 11Fasten the Door BracketFollow instructions which apply to your door typeas illustrated below or on the following page.A horizontal

ONE-PIECEDOORSPlease read and comply with the warnings andreinforcement instructions on the previous page.They apply to one-piece doors also.• Center

INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTION

ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4:• Fasten the straight and curved door arm sectionstogether to the longest possible length (with

ADJUSTMENT STEP 1Adjust the UP and DOWN TravelLimitsLimit adjustment settings regulate the points at whichthe door will stop when moving up or down.To

ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the backpanel of the motor unit. Force adjustment settingsregulate the amoun

ADJUSTMENT STEP 3Test the Safety Reversal SystemTEST• With the door fully open, place a 1-1/2" (3.8 cm)board (or a 2x4 laid flat) on the floor, c

Preparing your garage doorBefore you begin:• Disable locks.• Remove any ropes connected to garage door.• Complete the following test to make sure your

OPERATIONIMPORTANT SAFETY INSTRUCTIONSTo reducethe riskof severe injuryor death:1. READAND FOLLOWALL WARNINGSANDINSTRUCTIONS.2. ALWAYSkeep remote cont

Using the Wall.Mounted To Open the Door ManuallyDoor ControlTHE DOOR CONTROLPress the push bar to open or closethe door. Press again to reverse thedoo

CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may FORCECONTROLScause some minor changesin door operation requiringsome re-adjustme

HAVING A PROBLEM?1, My door will not close and the light bulbs blinkon my motor unit: The safety reversing sensormust be connected and aligned correct

Bell WireSafety SensorDiagnostic ChartSafety sensors wire open(broken or disconnected).ORSafety sensors wireshorted or black/whitewire reversed,Door c

PROGRAMMINGNOTICE: If this Security+_ garage door opener is operated with a non-rolling code transmitter, the technicalmeasure in the receiver of the

To Add, Reprogram or Change a Keyless Entry PINNOTE: Your new Keyless Entry must be programmed to operate your garage door opener.USING THE "LEAR

REPAIR PARTSRail Assembly PartsInstallation Parts\/ \\, \13124915KEYNO,123456KEY PARTNO, NO,1 41A41662 41A5076-23456789101112131415J37PARTNO, DESCRIPT

Motor Unit Assembly Parts1918 17I_ 6,7_Brown16 15(Down) LIMIT SWITCHContact ASSEMBLYContact Contact Wire11KEYNO,124567891011PART KEY PARTNO. DESCRIPTI

ACCESSORIES139,53702/Emergency Key Release:Required for a garage with NOaccess door. Enables homeownerto open garage door manually fromoutside by dise

PlanningIdentify the type and height of your garage door.Survey your garage area to see if any of theconditions below apply to your installation. Addi

Your Homeiiiiiiiiiiiiiiiiii For repair-in your home-of all major brand appliancesiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilawn and garden equipment, or heati

Planning (Continued)ONE-PIECE DOOR INSTALLATIONS• Generally, a one-piece door does not requirereinforcement. If your door is lightweight, refer tothe

Carton InventoryYour garage door opener is packaged in two cartonswhich contain the motor unit and all parts illustratedbelow. Accessories will depend

Hardware InventorySeparate all hardware and group as shown below for the assembly and installation procedures.ASSEMBLY HARDWAREWashered Bolt Hex Bolt

ASSEMBLY STEP 1Assemble the Rail andAttach the Cable Pulley BracketTo avoid installation difficulties, do not run thegarage door opener until instruct

ASSEMBLY STEP 2Install the Trolley• Attach the trolley threaded shaft to the trolley withthe lock washer and nuts as shown.• As a temporary stop, inse